Link between KV-5000/KV-3000 and LK-G/LS
Extra List of Ladder Programs/Macros
A sample ladder program created with PROTOCOL STUDIO is shown as follows:
《LK-G3000》 <List of Mnemonics>
;MR000: Send Start Relay
;DM0: Receive DM
Normal ON PORT1
LD CR2002
Action enabled
OUT R32600
LD R33900
ANP MR000
PORT1 Send/receive start PORT1
Action ready delay Relay Macro start 1 SET R32000
LDP R33300
AND R32700
BMOV DM10102 DM0 #4
PORT1 receive PORT1 receive PORT1 Receive DM RES R32000
read request 1 parity1 Macro variable leading address
start
PORT1
Macro start 1
ONE POINT
The operand of BMOV for the third line (the 10th line in the List of Mnemonics) in the ladder changes to the
following when the LS-7000 series are used: DM10102 to DM10105, #4 to #2.
Some macros registered in the PROTOCOL STUDIO are shown in the following table:
LK-G3000 LS-7000
Moving to the communication mode Timing ON
Moving to the normal mode Timing OFF
Timing ON Reset
Timing OFF Auto zero ON
Auto-Zero ON Auto zero OFF
Auto-Zero OFF Change program No.
Reset Calculation
Program No. change Average
Calculation method setting Measurement mode
Scaling setting Offset
Measurement mode setting Analog reference value
Minimum display unit setting Proof theoretical
Sampling rate setting Group determination
11
KV-5000/KV-3000 和 LK-G/LS 之间的链路
Extra 梯形图程序 / 宏一览
以下是使用了通过 PROTOCOL STUDIO 制作的通信协议的参考梯形图。
《LK-G3000 时》 《助记符清单》
;MR000 ：发信开始继电器
;DM0 ：收信 DM
常时 ON 端口 1
LD CR2002
动作使能
OUT R32600
LD R33900
ANP MR000
端口 1 端口 1
收发信开始
宏开始 1 SET R32000
动作就绪 继电器
LDP R33300
AND R32700
BMOV DM10102 DM0 #4
端口 1 接收 端口 1 接收 端口 1 收信 DM 首 RES R32000
读取请求 1 校验 1 宏变量起始 地址
端口 1
宏开始 1
单点
LS-7000 系列时，梯形图第 3 行（助记符清单第 10 行）的 BMOV 命令的操作数作如下变更 ：
DM10102 => DM10105、#4 => #2。
以下是 PROTOCOL STUDIO 中登录的一部分宏。
LK-G3000 LS-7000
Moving to the communication mode Timing ON
Moving to the normal mode Timing OFF
Timing ON Reset
Timing OFF Auto zero ON
Auto-Zero ON Auto zero OFF
Auto-Zero OFF Change program No.
Reset Calculation
Program No. change Average
Calculation method setting Measurement mode
Scaling setting Offset
Measurement mode setting Analog reference value
Minimum display unit setting Proof theoretical
Sampling rate setting Group determination
11
24
日本語 英 語 中国語
実験 Experiment
実際原価 Practical cost
し
︱
実在庫 Practical inventory
し
実寸法 Actual size
実測 Actual measurement
湿度 Humidity
質量 Mass
自動運転 Auto-run
自動送り Power feed
自働化 Automation
始動完了 Starting completion signal
自動組立 Automatic assembly
自動工具交換装置 Automatic tool changer
始動時バイアス速度 Offset speed at starting
自動車 Automobile
自動車部品 Automobole parts
自動制御 Automatic control
自動設定 Automatic setting
自動旋盤 Automatic lathe
始動トルク Starting torque
自動補正 Auto correction
シフトJISコード表 Shift-JIS code table
シフトコード Shift code
絞り Diaphragm
絞り加工 Spinning
絞り型 Drawing die
シミュレーション Simulation
シミュレータ Simulator
シム Shim
シャーリング Shearing
2 Enter the text
STEP
(1) Click the outline text to select it (Parts are already selected immediately after
they are laid out). Configure the outline text in the properties window.
You can select any font.
Single
click
(2) Enter the string in the properties window. Use Auto Fit to make the
text fit within the selected
area.
Enter the text.
VT STUDIO allows you to easily span characters horizontally by specifying the pitch.
Automatically
adjusts the pitch.
Pitch adjustment
18 VT STUDIO Quick Design Text
R EDUCED LABOR INCREASED VISIBILITY
Changed color of cell lines
Cell lines/Cell background
and background
Changing lines and background
color for improved visibility
Copy/Auto fill
Just like spreadsheet programs, VT
STUDIO allows the user to copy to
multiple cells by selecting a cell and
dragging over a range.
The device assignments increment
automatically.
Device numbers increment
for each copied part
Application
EQUIPMENT OPERATION GUIDANCE SCREENS
The spreadsheet-like operation makes
creating intuitive tables easier than ever.
13
2 Enter the text
STEP
(1) Click the outline text to select it (Parts are already selected immediately after
they are laid out). Configure the outline text in the properties window.
You can select any font.
Single
click
(2) Enter the string in the properties window. Use Auto Fit to make the
text fit within the selected
area.
Enter the text.
VT STUDIO allows you to easily span characters horizontally by specifying the pitch.
Automatically
adjusts the pitch.
Pitch adjustment
18 VT STUDIO Quick Design Text
R EDUCED LABOR INCREASED VISIBILITY
Changed color of cell lines
Cell lines/Cell background
and background
Changing lines and background
color for improved visibility
Copy/Auto fill
Just like spreadsheet programs, VT
STUDIO allows the user to copy to
multiple cells by selecting a cell and
dragging over a range.
The device assignments increment
automatically.
Device numbers increment
for each copied part
Application
EQUIPMENT OPERATION GUIDANCE SCREENS
The spreadsheet-like operation makes
creating intuitive tables easier than ever.
13
Details on label settings
Select Nameplate
ON or OFF status selection The font size automatically
Applies only to indicators and adjusts to fit within the part.
indicator switches.
Font selection
Use any font installed on the
PC.
Auto fit
Label placement
Select from center, top,
bottom, left, right.
Text color and effects
Select text color, bold type, or
Enter the text to appear on the
other effects.
label. For an indicator or
indicator switch, enter the text
for both states, ON and OFF.
Changing the style of a switch
Details on style settings
Select Style
Select a style. The style
names are the same names
used in the catalog.
Select a color
The same colors used in the
catalog can be set here as well.
You can create your own parts
by combining styles in the
catalog with images taken with
a digital camera.
10 VT STUDIO Quick Design Text
REDUCED LABOR
Application
DEVICE MONITOR SCREEN FOR A POSITIONING CONTROLLER UNIT
Select multiple items and drag and drop them onto the screen to instantly create multiple parts with labels and device
assignments. Easily build monitoring screens for debugging.
Monitoring screen for a
positioning controller unit
Batch part creation can also create
monitoring screens for expansion units in
just one click.
Style and label settings applied
when creating parts by
importing from the device
comments list can be
customized.
Edit Optional settings
O PERATIONS SCREEN FOR INVERTER CONNECTIONS
VT STUDIO comes with pre-registered device comments for external devices allowing the user to easily create screens
for external devices.
Simply paste the operation
Device comments list for inverters Frequency monitor
controls and parameters
while viewing the device
comments
Run command
To import device comments for
external devices, click
Import Auto register
5
06
I want to align numeric displays
Tables and numeric displays are difficult to layout…
I want to make my tables easy to read, but it’s time-consuming…
Useful VT3 Function
TABLE CREATION FUNCTION
Registering makes adjustments easy
Using the Table Creation function, the user can control and adjust the table and registered parts such as numeric
displays as a single unit. This makes it possible to create good-looking tables without spending time adjusting the table
and numeric parts separately.
Parts Table
Register numeric displays and
other parts with the mouse
These functions allow the user to quickly make good-looking tables
Adjusts the cell width
Width/height auto adjust
Automatically adjusts the width and
height balance for numeric displays in
a table.
Aligns numeric displays in each
cell in a single operation
In-cell alignment
Adjust positioning in one step
12
翻訳キーワード集
